Site will be offline for up to 2-hours, beginning at 4pm PST for routine maintenance and catalog improvements.

550cc/52lb EV14, BLACK-OPS M-SERIES FUEL INJECTORS. LS2, SRT-8, Focus

Custom Fiveo
Part Number: Black-Ops M52, M52U550-X8
Flow Rate: 52 lbs/hr @ 43.5 psi
Flow Rate: Please select an option below
Resistance: 12.5 Ohms
High Performance
$85.00 (USD)
Subtotal: $85.00

M-Series Black-Ops M52 550cc/min, 52lbs/hr

PRICE REDUCTION: NEW LOWER PRICE
USE THIS INJECTOR FOR HIGHLY MODIFIED ENGINES ONLY.

  • M-Series custom flow-matched 52lbs/hr, 550cc/min, high flowing fuel injectors.
  • Delivered in flow-balanced sets
  • Price listed is for a single injector

Use for super street or racing, single or multi-valve, normally aspirated or forced-air induction engine applications:

Our injectors are custom-manufactured from brand new American-made fuel injector "cores" in large-quantity batches to achieve the highest quality product. The resulting sets are all-fuels rated; including gasoline (MTBE), and E-85. The finished injectors are then flowed and inscribed with a control number. Data is recorded for each injector. They are then hermetically-sealed and placed in matched sets ready for shipping.
You don't get this kind of technology from an OE injector.

FLOW CHART: Each set is sold with a complete flow-data chart indicating individual static flow rates at 3.0, 3.5, and 4.0 BAR. As well as 3.0 BAR dynamic pulse testing for idle (15% duty-cycle) and 50% duty-cycle. Along with a complete dead time off-set (latency) table. Flow matching was done with industry-standard equipment of the highest quality.
The tests were performed at varying temperatures to achieve realistic results. Linear tuning with excellent low-end, and idle rpm.

SPECIAL NOTE TO OUR E85 USERS:
Ethanol tends to "dry" the orifices. Customers should be made aware that this can be a problem with some fuel injectors. And may cause a "sticking" problem. It is suggested that a tank of 91-98 octane gasoline be run to every 5 or 6 tanks of Ethanol to re-lube not only the fuel injectors, but the entire fuel component system. This is also considered to be good maintainance, but not essential, for stainless steel based fuel injectors.

 


The test was performed at varying temperatures to achieve realistic results.Our injectors are custom-manufactured from brand new American-made fuel injector "cores" in large-quantity batches to achieve the highest quality product. The resulting sets are all-fuels rated; including gasoline (MTBE), and E-85. The finished injectors are then flowed and inscribed with a control number. Data is recorded for each injector. They are then sealed and placed in matched sets ready for shipping.
You don't get this kind of technology from an OE injector.

 

This is a high performance, high volume fuel injector.
The fuel delivery is from a single-hole, ball/disc fuel nozzle.
Wide cone-shape spray pattern for maximum fuel atomization.

Body Design: Composite plastic

Injector type: M-Series, saturated

Flow rate:

550 cc/min 3.0 BAR, 52 lbs/hr at 43.5 psi.

600 cc/min 3.5 BAR, 57 lbs/hr at 50.8 psi.

655 cc/min 4.0 BAR, 62 lbs/hr at 58.0 psi.

Length: 2.3/8 inches, 64 mm

Diameter: 9/16 inches, 14 mm

Orings: Top and bottom, 14.5 mm

Resistance: 12.5 Ohms

Electrical connector type: USCAR

More Information
Manufacturer Custom Fiveo
OEM or Aftermarket High Performance
Flow Rate Please select an option below
Flow Rate 52 lbs/hr @ 43.5 psi
Impedance 12.5 Ohms
Part Number Black-Ops M52, M52U550-X8
Join the FiveO Team
Receive Emails on New Product Announcements, Special Promos, Sales and More