This Siemens 3172 custom milled set includes 2-Primary
and 2-Secondary
550cc stock-replacement Siemens high resistance, 13 Ohm, fuel injectors. Sold with EV1electrical connector pigtails.
In stock - Ready for shipment

See higher rated Siemens injectors for the RX7. Siemens Upgrades for RX7

This Siemens 3102 custom milled set includes 2-Primary
and 2-Secondary
550cc stock-replacement Siemens low resistance, 2.3 Ohm, fuel injectors. Sold with EV1 electrical connector pigtails.
In stock - Ready for shipment

See higher rated Siemens injectors for the RX7. Siemens Upgrades for RX7

Ford Racing 846 is out of production. We sell the Bosch 842 "Indy Blue"
Please note: These are brand new, high quality Bosch performance fuel injectors
custom milled to your engine specs.

2.8 Ohms Low Impedance 55lbs/hr - 575cc/min P/N 3102 Siemens Deka

We custom mill this Siemens 3102 to replace Denso p/n 195500-1370 for the Mazda RX7. See our Custom Milled page.
*All new Siemens injectors sold with a 100% Warranty.

Sold with
EV1 electrical connectors
May require splicing.

Please note: These are brand new, high quality Siemens performance fuel injectors
custom milled to your engine specs.
Siemens 3145 72lbs/hr (750cc/min.)
Low Resistance: 2.5 Ohms

Sold in sets of two (2)
for primary or secondary
fuel injectors
for 1985-92 RX-7
Sold with electrical connectors

Use for super street or racing 4 cylinder applications:

VW, Audi, Ford, Mitsubishi, etc.

Body Design: Metal and composite plastic

Flow rate: 750cc/min @ 3 bar, 72lbs/hr @ 43 psi

Coil resistance: 2.5 Ohms

Length: 3 inches, 74 mm

Diameter: 24 mm

O-rings: Top and bottom, 14.5 mm

Part numbers available:

FI-11445, 3145 imprinted on body of injector.

We custom mill this Siemens 3145 for the 03-04 Mitsu EVO and the 95-99 Eclipse 2.0. See our Custom Milled page.

We buy brand new Siemens Deka fuel injectors direct from the manufacturer.

You are puchasing a set of high performance,

low impedance, flow-matched Bosch 150lbs/hr - 1600cc/min

fuel injectors.

These injectors are part of the new "ASPHALT" series of flow matched black top peak and hold

1100cc, 1400cc, 1600cc and 2000cc fuel injectors.

This is not a "drilled out" injector.

They are all custom milled from Bosch "blanks".

All sets come with a flow DATA SHEET

This set of Bosch fuel injectors was custom milled to flow 150lbs/hr at 43.5 psi (3 bar).

See flow rate chart below.

The injectors incorporate a single pintle fuel delivery nozzle with a wide cone spray for excellent fuel atomization.

Price: $775.99 per set of 12

SPECIAL NOTE to our customers: You will receive flow matched sets of Bosch fuel injectors. 14mm orings are supplied for installation. This injector set is sold with a money back guarantee. If you are not 100% satisfied we will exchange or refund your purchase price for returned, unused and uninstalled fuel injectors. You pay only the shipping.

Injector Body Design: Metal and composite plastic

Flow rates: Listed at 80% duty cycle

We use the industry standard Heptane as our testing agent.

153 lbs/hr, 1600 cc/min at 43.5 psi (3 bar)

163 lbs/hr, 1715 cc/min at 50 psi (3-1/2 bar)

176 lbs/hr, 1850 cc/min at 58psi (4 bar)

This Bosch injector will function at rail pressures in excess of 101psi, 7 bar.

Excellent low pulse width response with predictable response down to 2ms.

Excellent atomization for modern multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

Injector type: EV1

Application: Super-street and racing, natually- and forced-aspirated engines.

Fuel Delivery: Single-hole Pintle

Electrical Connector: EV1, minitimer

Spray type: wide cone, maximum atomization

Length: 3 inches, 74 mm

Diameter: 24 mm

Orings: Top and bottom, 14.5 mm

Resistance: 3.2 Ohms

Fuel types: Gasoline, Methanol, E85, E25, E10

You are puchasing a set of high performance,

low impedance, flow-matched Bosch - 1200cc/min

fuel injectors.

These injectors are part of the new "ASPHALT" series of flow matched black top peak and hold

1100cc, 1400cc, 1600cc and 2000cc fuel injectors.

This is not a "drilled out" injector.

They are all custom milled from Bosch "blanks".

All sets come with a flow DATA SHEET

This set of Bosch fuel injectors was custom milled to flow 1200cc/min at 43.5 psi (3 bar).

See flow rate chart below.

The injectors incorporate a single pintle fuel delivery nozzle with a wide cone spray for excellent fuel atomization.

Price: $259.99 per set of 4

Use for all forced-air induction 4 cylinder engines.

SPECIAL NOTE to our customers: This is a flow matched set of Bosch fuel injectors. 14mm orings are supplied for installation. This injector set is sold with a money back guarantee. If you are not 100% satisfied we will exchange or refund your purchase price for returned, unused and uninstalled fuel injectors. You pay only the shipping.

Injector Body Design: Metal and composite plastic

Flow rates: Listed at 80% duty cycle

We use the industry standard Heptane as our testing agent.

1200 cc/min at 43.5 psi (3 bar)

1290 cc/min at 50 psi (3-1/2 bar)

1380 cc/min at 58psi (4 bar)

This Bosch injector will function at rail pressures in excess of 101lbs/hr, 7 bar.

Excellent low pulse width response with predictable response down to 2ms.

Excellent atomization for modern multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

Injector type: EV1

Application: Super-street and racing, natually- and forced-aspirated engines.

Fuel Delivery: Single-hole Pintle

Electrical Connector: EV1, minitimer

Spray type: wide cone, maximum atomization

Length: 3 inches, 74 mm

Diameter: 16 mm

Orings: Top and bottom, 14.5 mm

Resistance: 3.2 Ohms

Fuel types: Gasoline, Methanol, E85, E25, E10

Fiveomotorsport has been a Power Seller on ebay since 2000.

We are fuel injector experts - email with your questions.

All injector sets are sold with the manufacturer's warranty plus our 36 Months/Unlimited Miles Warranty.

These Bosch injectors are guaranteed flow matched.

You are puchasing a set of high performance,

low impedance, flow-matched Bosch 135lbs/hr - 1400cc/min

fuel injectors.

These injectors are part of the new "ASPHALT" series of flow matched black top peak and hold

1100cc, 1400cc, 1600cc and 2000cc fuel injectors.

This is not a "drilled out" injector.

They are all custom milled from Bosch "blanks".

All sets come with a flow DATA SHEET

This set of Bosch fuel injectors was custom milled to flow 135lbs/hr at 43.5 psi (3 bar).

See flow rate chart below.

The injectors incorporate a single pintle fuel delivery nozzle with a wide cone spray for excellent fuel atomization.

Price: $519.99 per set of 8

Use for all forced-air induction 8 cylinder engines.

SPECIAL NOTE to our customers: This is a flow matched set of Bosch fuel injectors. 14mm orings are supplied for installation. This injector set is sold with a money back guarantee. If you are not 100% satisfied we will exchange or refund your purchase price for returned, unused and uninstalled fuel injectors. You pay only the shipping.

Injector Body Design: Metal and composite plastic

Flow rates: Listed at 80% duty cycle

(These are true and tested flow rates of this individual set of 8 fuel injectors).

We use the industry standard Heptane as our testing agent.

135 lbs/hr, 1400 cc/min at 43.5 psi (3 bar)

143 lbs/hr, 1500 cc/min at 50 psi (3-1/2 bar)

154 lbs/hr, 1610 cc/min at 58psi (4 bar)

This Bosch injector will function at rail pressures in excess of 101 psi, 7 bar.

Excellent low pulse width response with predictable response down to 2ms.

Excellent atomization for modern multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

Injector type: EV1

Application: Super-street and racing, natually- and forced-aspirated engines.

Fuel Delivery: Single-hole Pintle

Electrical Connector: EV1, minitimer

Spray type: wide cone, maximum atomization

Length: 3 inches, 74 mm

Diameter: 23 mm

Orings: Top and bottom, 14.5 mm

Resistance: 3.2 Ohms

Fuel types: Gasoline, Methanol, E85, E25, E10

Fiveomotorsport has been a Power Seller on ebay since 2000.

We are fuel injector experts - email with your questions.

All injector sets are sold with the manufacturer's warranty plus our 36 Months/Unlimited Miles Warranty.

These Bosch injectors are guaranteed flow matched.

You are puchasing a set of high performance,

low impedance, flow-matched Bosch 190lbs/hr - 2000cc/min

fuel injectors. (See additional flow specs below).

These injectors are part of the new "ASPHALT" series of flow matched black top peak and hold

1100cc, 1400cc, 1600cc and 2000cc fuel injectors.

This is not a "drilled out" injector.

They are all custom milled from Bosch "blanks".

All sets come with a flow DATA SHEET

This set of Bosch fuel injectors was custom milled to flow 190lbs/hr at 43.5 psi (3 bar).

See flow rate chart below.

The injectors incorporate a single pintle fuel delivery nozzle with a wide cone spray for excellent fuel atomization.

Use for all forced-air and naturally aspirated induction engines.

SPECIAL NOTE to our customers: This is a flow matched set of Bosch fuel injectors. 14mm orings are supplied for installation. This injector set is sold with a money back guarantee. If you are not 100% satisfied we will exchange or refund your purchase price for returned, unused and uninstalled fuel injectors. You pay only the shipping.

Injector Body Design: Metal and composite plastic

Flow rates: Listed at 80% duty cycle

We use the industry standard Heptane as our testing agent.

183 lbs/hr, 1930 cc/min at 43.5 psi (3 bar)

196 lbs/hr, 2060 cc/min at 49 psi (3-1/2 bar)

212 lbs/hr, 2210 cc/min at 58psi (4 bar)

This Bosch injector will function at rail pressures in excess of 101 psi, 7 bar.

Excellent low pulse width response with predictable response down to 2ms.

Excellent atomization for modern multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

Injector type: EV1

Application: Super-street and racing, natually- and forced-aspirated engines.

Fuel Delivery: Single-hole Pintle

Electrical Connector: EV1, minitimer

Spray type: wide cone, maximum atomization

Length: 3 inches, 74 mm

Diameter: 16 mm

Orings: Top and bottom, 14.5 mm

Resistance: 3.2 Ohms

Fuel types: Gasoline, Methanol, E85, E25, E10

Fiveomotorsport has been a Power Seller on ebay since 2000.

We are fuel injector experts - email with your questions.

All injector sets are sold with the manufacturer's warranty plus our 36 Months/Unlimited Miles Warranty.

These Bosch injectors are guaranteed flow matched.

Body Design: Pencil, composite plastic

Flow rate: 60lbs/hr at 43.5 PSI (3 BAR)

Length: 3 inches, 74 mm

Diameter: 19 mm

O-rings: Top and bottom, 14.5 mm

Part numbers available:

107961 - Long EV1 electrical connector

Coil Resistance: 14 Ohms (high resistance, saturated).

Use for super street or racing applications:  Domestic and Import Ford, Chrysler, GM, BMW, VW, Audi, Mitsubishi, etc.

Can be milled to fit most imports.

*We buy brand new Siemens Deka fuel injectors direct from the manufacturer.  All new Siemens injectors sold with a 100% Warranty.

This Siemens 625-635cc injector set has been custom fitted for all Toyota 1ZZ and 2ZZ Engines, Mitsu Evo, etc.

(Use for super street or racing 4 cylinder applications).

You are purchasing a BRAND NEW set of manufacturer's

Siemens fuel injectors -

Brand New High Flowing Fuel Injector Set

The Siemens brand is a respected name in high performance and racing parts.

WE buy this Mototron 80# and all our fuel injectors in bulk packs.

Fiveo routinely test and retest samples from each shipment for quality control.

We do not provide flow data sheets.

Fiveomotorsport guarantees this set to be matched

and better than +/- 1% according to the manufacture'r specifications.

We have never had a blow-out or coil failure of any Siemens Mototron fuel injector.

No 107961 Mototron fuel injector has ever been found to be outside of the manufacturerr's advertised speciftications.

Fiveo's Exclusive Guarantee:

If you ever have an injector go outside spec or fail for any reason when functioning within the manufacturer's

stated operating conditions, We will replace it with a brand new fuel injector.

You are purchasing a brand new high performance Siemens fuel injector set.

Mfg., Part number on injector: 107961

Flow Rate: 630cc/min at 43.5 PSI

Flow Rate: 60LBS/HR at 43.5 PSI

Resistance: 12-16 Ohms

Voltage: 8-15 Volts, Nominal 13.5 Volts

Amperage: 1.0 Amps

Pressure: Min. 36 PSI (2.5 bar), Max. 130 PSI (9 bar)

Surface finish: black composite

All O-rings Included for installation.

This Bosch injector set is custom fitted for the OEM fuel rail and intake with 16 mm and 12 mm orings.

This injector will support gasoline, E10 ( Ore.) or E85.

$359.99 per set of 4 fuel injectors/connector adapters

This is a custom milled and flow-matched Bosch fuel injector set.

The Bosch brand is a respected name in high performance and racing parts.

This Generation III composite fuel injector is better suited to the high pressures of modern engines over the old fused plastic/metal body injectors.

None of our customers have ever reported a blowout or failed coil even with pressures

exceeding 100 psi. We have delivered this injector for street and off-road useage.

This Bosch injector has excellent high and low pulse width response times.

These sets are very consistant and will require no more than 1% trim for easy tuning

with accurate compensation down to 2 ms. The latency time is 0.85 ms.

(See additional specs below).

Fiveo's Exclusive Guarantee:

If you ever have an injector go outside spec or fail for any reason when functioning within the manufacture's stated operating conditions, whether in a street or racing application, we will replace it with a brand new fuel injector. We will only ask that you pay the shipping.

Injector type: Multi-hole disc, EV14

Flow pattern: wide cone for multi-valve engines

Part number: 02801580551000

Flow Rate: 1000cc/min at 43.5 PSI

Resistance: 12.8-14.5 Ohms, saturated

Voltage: 8-15 Volts, Nominal 13.5 Volts

Pressure: Min. 36 PSI (2.5 bar), Max. 130 PSI (7 bar)

Surface finish: Black composite with aluminum adapter

All O-rings Included for installation.

You are purchasing a set of custom milled and flow-matched Bosch EV14 fuel injectors for the AUDI AAN and Volvo B52 Series, BMW, etc., naturally aspirated or turbocharged/supercharged 4,5, 6, 8 or 12 cylinder engine.

This Bosch injector set fits the OEM fuel rail and intake. You may need a set of 12.5mm extenders and electrical connector adapters for complete fitment.

NOTE: You will need to purchase either a set of U.S.CAR electrical connector pigtails or adapters to fit the new injectors. And a set of 12.5mm length extenters with 14mm o-rings.

This injector will support gasoline, E10 (Ore.) or E85.

This is a custom milled and flow-matched Bosch fuel injector set.

The Bosch brand is a respected name in high performance and racing parts.

This EV14 composite fuel injector is better suited to the high pressures of modern engines over the old fused plastic/metal body injectors.

None of our customers have ever reported a blowout or failed coil even with pressures exceeding 90 psi. We have delivered this injector for street and off-road useage.

This Bosch 0280158055600 injector has excellent high and low pulse width response times.

These sets are very consistant and will require no more than 1% trim for easy tuning

with accurate compensation down to 0.7 ms.

(See additional specs below).

Fiveo's Exclusive Guarantee:

If you ever have an injector go outside spec or fail for any reason when functioning within the manufacture's stated operating conditions, whether in a street or racing application, we will replace it with a brand new fuel injector. We ask that you pay the shipping.

You are purchasing a brand new high performance Bosch fuel injector set.

Injector type: Single-hole disc, EV14

Flow pattern: wide cone for multi-valve engines

Tested Flow Rates:

650cc/min at 3 BAR

705cc/min at 3.5 BAR

760cc/min at 4 BAR

Resistance: 12.8-14.5 Ohms

Voltage: 8-15 Volts, Nominal 13.5 Volts

Pressure: Min. 36 PSI (2.5 bar), Max. 100 PSI (7 bar)

Dead Time: 0.7ms at 14 volts

Surface finish: Black composite

All Viton o-rings Included for installation.

You are purchasing a set of custom milled and flow-matched Bosch EV14 fuel injectors for the AUDI AAN and Volvo B52 Series turbocharged/supercharged 5 cylinder engine.

This Bosch injector set fits the OEM fuel rail and intake. You may need a set of 12.5mm extenders and electrical connector adapters for complete fitment.

NOTE: You will need to purchase either a set of U.S.CAR electrical connector pigtails or adapters to fit the new injectors. And a set of 12.5mm length extenters with 14mm o-rings.

This injector will support gasoline, E10 (Ore.) or E85.

This is a custom milled and flow-matched Bosch fuel injector set.

The Bosch brand is a respected name in high performance and racing parts.

This EV14 composite fuel injector is better suited to the high pressures of modern engines over the old fused plastic/metal body injectors.

None of our customers have ever reported a blowout or failed coil even with pressures exceeding 90 psi. We have delivered this injector for street and off-road useage.

This Bosch 0280158055600 injector has excellent high and low pulse width response times.

These sets are very consistant and will require no more than 1% trim for easy tuning

with accurate compensation down to 0.7 ms.

(See additional specs below).

Fiveo's Exclusive Guarantee:

If you ever have an injector go outside spec or fail for any reason when functioning within the manufacture's stated operating conditions, whether in a street or racing application, we will replace it with a brand new fuel injector. We ask that you pay the shipping.

You are purchasing a brand new high performance Bosch fuel injector set.

Injector type: Single-hole disc, EV14

Flow pattern: wide cone for multi-valve engines

Tested Flow Rates:

650cc/min at 3 BAR

705cc/min at 3.5 BAR

760cc/min at 4 BAR

Resistance: 12.8-14.5 Ohms

Voltage: 8-15 Volts, Nominal 13.5 Volts

Pressure: Min. 36 PSI (2.5 bar), Max. 100 PSI (7 bar)

Dead Time: 0.7ms at 14 volts

Surface finish: Black composite

All Viton o-rings Included for installation.

You are purchasing a BRAND NEW set of custom milled, and guaranteed

flow-matched set of 60lbs/hr Bosch EV14 fuel injectors - 8 high flowing injectors.

Use for super street or racing 8 cylinder, single or multi-valve, normally aspirated or forced-air induction engine applications:

Corvette LS2 V-8, Chrysler SRT-8, etc.

Use for up to 800 horsepower in a naturally aspirated engine.

This is a high performance, high volume fuel injector. The fuel delivery is from a single-hole disc. Wide cone-shape spray pattern for maximum fuel atomization.

Body Design: Composite plastic

Injector type: EV14, saturated

Flow rate:
625-635 cc/min 3.5 BAR, 60lbs/hr at 50 psi.
675-685 cc/min 4 BAR, 60lbs/hr at 58 psi.
750-760 cc/min 5 BAR, 60lbs/hr at 72.5 psi.

Length: 2.3/8 inches, 64 mm

Diameter: 9/16 inches, 14 mm

Orings: Top and bottom, 14.5 mm

Resistance: 12.5 Ohms

Electrical connector type: U.S. CAR

You are purchasing a BRAND NEW custom milled and flow-matched

set of manufacturer's 90lbs/hr Bosch EV14 fuel injectors - Can be used with extenders.

Use for super street or racing, single or multi-valve, forced-air induction engine applications using gasolinei or other green fuels.

This is a high performance, high volume fuel injector. These Bosch injectors have been highly modified and flow-matched to specific specifications. The fuel delivery is from a single-hole disc. Wide cone-shape spray pattern for maximum fuel atomization.

High resistance, no inline resistors or resistor box requires for use.

All New Generation Bosch injectors will function at rail pressures in excess of 130 psi, 9 bar.

Excellent low pulse width response with predictable response.

Excellent atomization for modern multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

Body Design: EV14, Composite plastic

Flow rates:

910-920 cc/min, 87 lbs/hr at 43.5 psi. (3 bar)

990-10005 cc/min, 95 lbs/hr at 50 psi. (3.5 bar)

1080-1095 cc/min, 103 lbs/hr at 58 psi. (4 bar)

Length: 2-3/8 inches, 64 mm

Diameter: 9/16 inches, 14 mm

Orings: Top and bottom, 14.5 mm

Resistance: 14.5 Ohms

Electrical connector type: EV6/U.S. CAR

Part number: 117910

tandard length 2-1/2 inch. Brand new flow matched set sold with data sheet.
1000cc/min at 3.5 Bar, 96lbs/hr at 50 psi.

Includes: 4 EV6/Denso electrical connector plug-in adapters
Bosch 550cc - WRX Modified, Hyundai

SPECIFICATIONS:
Injector type:
Multi-hole disc, EV14
Flow pattern: 6-hole wide cone for multi-valve engines
Part number: 0280158117 Custom Milled
Flow Rate: 550cc/min at 43.5 PSI (3 BAR)
Resistance: 12.8-14.5 Ohms
Voltage: 8-15 Volts, Nominal 13.5 Volts
Pressure: Min. 36 PSI (2.5 bar), Max. 100 PSI (7 bar)
Surface finish: Black composite
All 12 mm and 16 mm O-rings included for installation.

Viton Orings.

You are puchasing a set of six (6) Brand New high performance Japanese Electronics Corp (JECS)/Bosch fuel injectors - Custom Milled to flow 1000cc - SHIPPED WITH INDVIDUAL-SET FLOW DATA DOCUMENT.

This is a brand new set of high quality Nissan fuel injectors.

To insure a quality product our shop adheres to the highest standard milling and flow-matching using the industry's latest technology.

Whenever possible we don't remove original part numbers.

We leave the original equipment part numbers on the injector so you can see that you are getting high quality, major branded fuel injectors.

No fakes, copies or any off-shore or Chinese imports.

You receive the highest quality fuel injectors for superstreet and racing applications.

As part of our quality control, each injector has been marked/inscribbed by our technician with an individual control number and is part of a unique flow-matched set.

This injector set is for modified engines with high horsepower. See Chart below.

This injector will fit all 1990-99 Nissan SR20DE, KA24DE, VG30DE, VE30DE, VQ30DE.

You are purchasing a BRAND NEW set of manufacturer's

JECS fuel injectors - 6 brand new high performance OEM fuel injectors.

$539.99 per set of 6 fuel injectors.

Injector Body Design: Metal and composite plastic

Flow rates: Listed at 80% duty cycle

(These are true and tested flow rates of this individual set of 6 fuel injectors.

We use Heptane as our testing agent).

990-1000 cc/min at 43.5 psi (3 bar) 80% duty cycle

1070-1080 cc/min at 50 psi (3.5 bar)

1150-1160 cc/min at 58psi (4 bar)

All sets are shipped with a flow-data information document.

Excellent low pulse width with predictable response.

Excellent atomization for modern single and multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

SPECIAL NOTE: All orings are supplied for installation.

You are puchasing a set of six (6) Brand New high performance Japanese Electronics Corp (JECS)/Bosch fuel injectors - Custom Milled to flow 750cc - SHIPPED WITH INDVIDUAL-SET FLOW DATA DOCUMENT. 

This is a brand new set of high quality Nissan fuel injectors.

To insure a quality product our shop adheres to the highest standard milling and flow-matching using the industry's latest technology.

Whenever possible we don't remove original part numbers.
We leave the original equipment part numbers on the injector so you can see that you are getting high quality, major branded fuel injectors.
No fakes, copies or any off-shore or Chinese imports.

You receive the highest quality fuel injectors for superstreet and racing applications.

As part of our quality control, each injector has been marked/inscribbed by our technician with an individual control number and is part of a unique flow-matched set.

This injector set is for modified engines with high horsepower. See Chart below.

This injector will fit all 1990-99 Nissan SR20DE, KA24DE, VG30DE, VE30DE, VQ30DE.

You are purchasing a BRAND NEW set of manufacturer's

JECS fuel injectors - 6 brand new high performance OEM fuel injectors.

$499.99 per set of 6 fuel injectors.

Injector Body Design: Metal and composite plastic

Flow rates: Listed at 80% duty cycle

(These are true and tested flow rates of this individual set of 6 fuel injectors.

We use Heptane as our testing agent).

750cc/min at 43.5 psi (3 bar) 80% duty cycle
800cc/min at 50 psi (3.5 bar)
865cc/min at 58psi (4 bar)

All sets are shipped with a flow-data information document.

Excellent low pulse width with predictable response.

Excellent atomization for modern single and multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

 
SPECIAL NOTE: All orings are supplied for installation.

You are puchasing a set of six (6) Brand New high performance Japanese Electronics Corp (JECS)/Bosch fuel injectors - Custom Milled to flow 850cc - SHIPPED WITH INDVIDUAL-SET FLOW DATA DOCUMENT.

This is a brand new set of high quality Nissan fuel injectors.

To insure a quality product our shop adheres to the highest standard milling and flow-matching using the industry's latest technology.

Whenever possible we don't remove original part numbers.

We leave the original equipment part numbers on the injector so you can see that you are getting high quality, major branded fuel injectors.

No fakes, copies or any off-shore or Chinese imports.

You receive the highest quality fuel injectors for superstreet and racing applications.

As part of our quality control, each injector has been marked/inscribbed by our technician with an individual control number and is part of a unique flow-matched set.

This injector set is for modified engines with high horsepower. See Chart below.

This injector will fit all 1990-99 Nissan SR20DE, KA24DE, VG30DE, VE30DE, VQ30DE.

You are purchasing a BRAND NEW set of manufacturer's

JECS fuel injectors - 6 brand new high performance OEM fuel injectors.

$499.99 per set of 6 fuel injectors.

Injector Body Design: Metal and composite plastic

Flow rates: Listed at 80% duty cycle

(These are true and tested flow rates of this individual set of 6 fuel injectors.

We use Heptane as our testing agent).

850-860 cc/min at 43.5 psi (3 bar) 80% duty cycle

935-945 cc/min at 50 psi (3.5 bar)

1005-1015 cc/min at 58psi (4 bar)

All sets are shipped with a flow-data information document.

Excellent low pulse width with predictable response.

Excellent atomization for modern single and multi-valve engines.

This set will require no more than a 1% trim for easy tuning.

SPECIAL NOTE: All orings are supplied for installation.